Questron Synthetic Blend 10W-30

Test Results and PQIA Assessment

Product: Questron Synthetic Blend
Viscosity Grade: SAE 10W-30
Labeled: API SJ
Manufactured By: Responsible party not shown on product label

Purchased at: Niles, MI
Date of purchase: 11/24/2020
Website(s): 

Company Information: Unknown

Front Label
Back Label

Test Results and PQIA Assessment

Assessment Summary

The results of the tests conducted on this sample meet the SAE J300 specifications for the SAE Viscosity Grade listed on the product label, and are consistent with the listed API Service Categories.

Physical Properties

Elemental Analysis

Labeling

yello

ADVISORY: Consumers should take note that this product is labeled as an API SJ motor oil. Motor oils meeting this API Service Category are intended for use in vehicles built prior to 2002. Although not stated on the label, consumers should be aware of its limited use. 

The label on the product tested does not comply with the Fair Packaging and Labeling Act (FPLA) and the Uniform Packaging and Labeling Regulations or the National Institute of Standards and Technology’s uniform standards for packaging and labeling, contained in NIST Handbook 130. These regulations require that each package of consumer commodities bear a label on which there is the name and place of business of the manufacturer, packer, or distributor.

Although the laboratory tests conducted on this sample cannot be used alone to establish if the product tested meets a given API Service Category, they can be used to determine if it does not. The test results and PQIA assessment relates ONLY to the sample tested and the tests conducted.
Viscosity
Standard
Questron
Status
Viscosity 100°C cSt
9.3 to <12.5
9.6
Viscosity 40°C cSt
58.2
Viscosity Index
149
Cold Crank Viscosity at -25°C
7,000 Max
3,052
Cold Crank Viscosity at -30°C
6,600 Max
5,872

Viscosity is a critical measure that determines how thick or thin a lubricant is. Viscosity is measured by several methods to determine the behavior of motor oil during cold startups and while hot at operating temperatures. Motor oils must meet Society of Automotive Engineers (SAE) J-300 standards to conform to a specific viscosity grade. >>More

Viscosity Index measures the change in viscosity with temperature. Viscosity Index improver additives are used to optimize viscosity at different temperatures. >>More

Detergent Additives and Total Base Number (TBN)
Standard
Questron
Status
Calcium (ppm)
1,639
Magnesium (ppm)
27
Sodium (ppm)
<1
Barium (ppm)
<1
TBN, mg KOH/g (ASTM D2896)
5.6

Detergent additives help to keep metal surfaces in an engine clean by controlling formation of deposits (i.e. sludge, varnishes). Such deposits can harm an engine by clogging oil passages that lubricate an engine, increase wear and reduce engine performance. A blend of calcium and magnesium-based detergents are most commonly used. A shift towards increased use of magnesium was required to address the needs of new gasoline direct injected (GDI) engines. >>More 

Detergent additives also help prevent corrosive wear by neutralizing acids formed as a by-product of combustion and other processes in an engine. Total Base Number (TBN) is a laboratory test that measures an oil’s ability to neutralize such acids. >>More

Antiwear Additives (parts per million)
Standard
Questron
Status
Phosphorus
1,000 Max -a
634
Zinc
743
Molybdenum
6
Titanium
<1
Boron
10

Antiwear (AW) additives help protect metal surfaces against impact friction and wear between moving parts in an engine. Such additives work by adhering to metal surfaces and forming a protective film between moving surfaces. The most widely used AW additive are chemistries containing phosphorus and zinc. Some lubricant manufacturers also employ the use of antiwear additives containing boron, molybdenum and titanium among others.

Antiwear additives are multifunctional in that they also act as corrosion inhibitors and, more significantly, antioxidants.

For more on AW additives and other functional and performance additives used in motor oil… >>More

Contaminants (parts per million)
Standard
Questron
Status
Silicon*
5
Silver
<1
Aluminum
<1
Chromium
<1
Iron
<1
Nickel
<1
Lead
<1
Antimony
<1
Tin
<1
Copper
<1
Cadmium
<1
Vanadium
<1
Potassium
<1
Manganese
<1
Lithium
<1

Although motor oil is subject to contamination from a number of metals related to wear, and abrasive material in the form of silicon when in use, new motor oil typically does not contain such metals at any appreciable levels. The presence of these metals (iron, aluminum, copper, lead, nickel, tin, sodium, potassium, etc.) in a new motor oil can indicate contamination from used oil, rust, abrasives, and others introduced to the product during blending, packaging, and/or transportation. Such contaminants can be harmful to an engine. Some can also be part of an additive, such as copper or sodium, but these are not often seen.

*Whereas silicon in the form of polydimethylpolysiloxane is commonly used as an antifoamant in motor oil, such use typically does not exceed 10ppm in new motor oil. Levels much above indicate possible contamination with abrasive material, silicone-based sealers, and/or transformer and hydraulic oil.

Note1: Standards are established by API, SAE and others.
Note2: Test Method for metal analysis is ASTM D5185.

  1. This specification is expressed to two significant figures, therefore results up to 1,049 are considered on specification.

Viscosity is a critical measure that determines how thick or thin a lubricant is. Viscosity is measured by several methods to determine the behavior of motor oil during cold startups and while hot at operating temperatures. Motor oils must meet Society of Automotive Engineers (SAE) J-300 standards to conform to a specific viscosity grade. >>More

Viscosity Index measures the change in viscosity with temperature. Viscosity Index improver additives are used to optimize viscosity at different temperatures. >>More

Detergent additives help to keep metal surfaces in an engine clean by controlling formation of deposits (i.e. sludge, varnishes). Such deposits can harm an engine by clogging oil passages that lubricate an engine, increase wear and reduce engine performance. A blend of calcium and magnesium-based detergents are most commonly used. A shift towards increased use of magnesium was required to address the needs of new gasoline direct injected (GDI) engines.

Detergent additives also help prevent corrosive wear by neutralizing acids formed as a by-product of combustion and other processes in an engine. Total Base Number (TBN) is a laboratory test that measures an oil’s ability to neutralize such acids. >>More

Antiwear (AW) additives help protect metal surfaces against impact friction and wear between moving parts in an engine. Such additives work by adhering to metal surfaces and forming a protective film between moving surfaces. The most widely used AW additive are chemistries containing phosphorus and zinc. Some lubricant manufacturers also employ the use of antiwear additives containing boron, molybdenum and titanium among others.

Antiwear additives are multifunctional in that they also act as corrosion inhibitors and, more significantly, antioxidants.

For more on AW additives and other functional and performance additives used in motor oil… >>More

Contaminants: Although motor oil is subject to contamination from a number of metals related to wear, and abrasive material in the form of silicon when in use, new motor oil typically does not contain such metals at any appreciable levels. The presence of these metals (iron, aluminum, copper, lead, nickel, tin, sodium, potassium, etc.) in a new motor oil can indicate contamination from used oil, rust, abrasives, and others introduced to the product during blending, packaging, and/or transportation. Such contaminants can be harmful to an engine. Some can also be part of an additive, such as copper or sodium, but these are not often seen these days.

*Whereas silicon in the form of polydimethylpolysiloxane is commonly used as an antifoamant in motor oil, such use typically does not exceed 10ppm in new motor oil. Levels much above indicate possible contamination with abrasive material, silicone-based sealers, and/or transformer and hydraulic oil.

PASSENGER CAR MOTOR OIL

PETROLEUM QUALITY INSTITUTE OF AMERICA SAMPLE SUMMARY/PASSENGER CAR MOTOR OIL Passenger car motor oil is the lifeblood of your engine. In addition to lubricating moving

Read More »

ANTIFREEZE & COOLANT

PETROLEUM QUALITY INSTITUTE OF AMERICA SAMPLE SUMMARY FOR ANTIFREEZE & COOLANT Antifreeze/coolant is critical for protecting engines. The primary

Read More »